Briggs & Stratton 71010 100 Amp Automatic Transfer Switch with Service Entrance Disconnect and ACCM

Designed for reliability against back feeding to the utility lines during an outage, the Briggs & Stratton 100 Amp automatic transfer switch features a service entrance disconnect and ACCM (AC Power Control Module). With the ability to run up to a 4-ton air conditioner with no worries of the generator shutting down, the switch is able to supply power to all circuits of your home or small business, and automatically manages the critical loads. Custom made exclusively for Briggs & Stratton Power Products standby generator systems, the switch reduces the overall energy cost by giving you the power you need exactly when you need it. The switch is adequate for either indoor or outdoor installation for added versatility.

The Preliminary Tool Kit

1. Crosscut handsaw, 22": This is technically a panel saw. It is useful for breaking down large planks you before flatten them.

2. Backsaw, 10": Presumably a carcase saw and filed crosscut, this tool will make your finishing cuts and is typically used with the bench hook.

3. Dovetail saw, 8": We prefer a 15-point saw that is filed for ripping cuts.

4. Jack plane: Hayward seems to prefer this plane for processing rough lumber. A 14"-long plane is typical.

5. Fore plane: Hayward seems to prefer this size plane (about 18") for shooting the edges of boards instead of a jointer plane.

6. Smoothing plane: The smoothing plane is the last plane to touch the work before scrapers or sandpaper. A 10"-long plane is a typical size.

7. Firmer chisels, 1/4" and 3/4": These were once common tools without the beveled edges that are common in catalogs today.

8. Warrington hammer: These small hammers have a cross-pane on one end for starting brad nails. Very handy and still available.

9. Mallet, 5" head. For driving chisels. Beech is the preferred wood.

10. Nail punch, fine: A small tool for setting nail heads below the wood's surface with a few short blows.

11. Pincers: A handy tool for pulling errant nails.

12. Screwdrivers, 8" and 3": Traditionally, these would be straight drivers. You'll also need Phillips, square-drive and others.

13. Cutting gauge: A marking tool with a knife for making its mark (instead of a pin).

14. Ratcheting brace, 8": Still useful, even in a power-tool shop.

15. Auger bit, 3/8".

16. Twist or brad-point bit, 3/16".

17. Countersink bit.

18. Center bit, 3/4": A bit for making flat-bottomed holes. Now Forstners are the standard.

19. Brad awl: Designed to start holes for nails and small screws.

20. Try square, 6".

21. Card scraper: This tool cleans up tear-out left by the smoothing plane.

22. Oilstone: Buy one with coarse and fine grits. Waterstones are now common.

23. Folding rule: Or a tape measure.

Useful Additional Tools

1. Bow saw, 12": This saw is useful for deep and curved cuts.

2. Keyhole saw: Used for fine work, particularly keyholes. These days one with a Japanese tooth pattern are more common and useful.

3: Coping saw: Useful for clearing out waste between dovetails and shallow curved cuts.

4. Bullnose plane: A now-uncommon tool for cleaning up rabbets.

5. Shoulder plane: A useful tool for trimming the cheeks and shoulders of tenons.

6. Compass plane: If you do circular work, this plane is helpful. Others never need it.

7. Rabbet plane: For the woodworker who prefers to cut rabbets by hand.

8. Toothing plane: A useful plane for roughing up surfaces prior to veneering.

9. Plow plane: A useful hand tool for making grooves and small rabbets. Not found in a typical power-tool shop.

10.Firmer chisels, 1/8" and 1/2".

11. Paring chisel, 1-1/2": Useful for a wide variety of fine cuts. Beveled edges are typical.

12.Mortise chisels, 5/16": If you work with machine-processed stock, you'll probably want a 1/4" tool instead.

13. Patternmaker's hammer: Like the Warrington next to it, but smaller.

14. Marking gauge: A gauge with a pin used for marking across and with the grain.

15. Mortise gauge: A marking gauge with two cutters to mark the two walls of a mortise simultaneously.

16. Spokeshave, wood body: Useful for curved shapes in easy-to-cut woods.

17. Auger bits, 1/4" and 1/2".

18. Center bits, 1" or as required: Again, substitute Forstners. Buy them as you need them.

19. Sash clamps, 36": Begin with one pair and purchase as needed.

20.C-clamps: A modern equivalent would also be F-style clamps.

21. Handscrews: Useful for all sorts of tapered and odd workholding needs.

22. Try square or combination square, 12".

23. Miter square: Useful for laying out and checking mitered work.

24. Sliding bevel, 8": For marking and measuring angles other than 90.

26. Gouge: A large tool for removing large amounts of wood quickly - not a carving tool.

26. Surform tool: It looks like a cheese grater and is used for shaping curved and compound work, such as cabriole legs.

27. Router plane: Used to trim tenon cheeks, deepen grooves and to cut hinge mortises.

28. Dividers: Basic tools that step off dovetails or other joinery.

Homemade Tools and Jigs

1. Miter block: A sawing device used to help cut small miters.

2. Miter box: A more complex and accurate device for cutting miters in mouldings.

3. Shooting board, 36" long: An appliance used to plane the long edges of boards true.

4. Straightedge: Make as many as you need; they're wood.

5.Square, 24": Useful for laying out joinery full-scale on cabinet sides.

6. Winding sticks: Two identically sized, straight sticks used to check boards for twisting and cupping.

7. Oilstone case.

8. Veneering hammer: This tool presses veneer against its substrate.

9. Bench hook: An essential appliance for accurate crosscuts with a handsaw.

10. Scratch stock: A small tool with homemade cutters filed to cut small shapes, such as beads.

11.Miter template: An appliance clamped to your work that allows you to chisel accurate miters.

Power Equipment

1. 10" table saw

2. 8" jointer

3.12" benchtop planer

4.1/2" drill

5. Random-orbit sander

6. Drill press or hollow-chisel mortiser

7. Jigsaw or band saw

8. Two-base router kit (2hp)

9. 10" miter saw

----------------

http://www.popularwoodworking.com

http://www.popularwoodworking.com/tools/

Copyright 2009 F+W Media Inc. All Rights Reserved.

generator diesel